When you say waterpump and main water pump you loose me. I have no idea what your talking about. Transfer/ supply/auxiliary supply pump??? Those terms would make me think that you carry water and is supplied to the machine by this pump . Where as ,main/pressure/ high pressure or name ie:cat/general/ hipro would make me assume that you're talking about the pump that supplies soulition to your wand . Then there's the wastepump i dont know what else you can call that one but waterpump pump and main pump can be interpreted differently . But with that said i don't know about your machine specifically but generally speaking the tachometer has a magnetic pickup and so machines mount this pickup on the main pressure pump and attaches a magnet on the back ( pump side) of the clutch pulley that pulley generally speaking again , turns much slower than engine or blower and is compensated electronically with a setting button on the tach. Perhaps with the work you have recently been doing in that general area youve inadvertently knocked this outa whack . I tack my machine off the driveshaft and measure blower speed below is a picture of mine yours will probably look different but worhs the same ill try to find another picture and edit with it couldn't easily find it but Google says the location is on the blower drive pulley
So Robert that you introduced me to at MF and Dwain here helped me get that fixed promptly. Then the rest of the needed repairs followed 1 after the other, with Dwain saving my arse, and teaching me precious knowledge.Does your machine completely shut down or does the van engine drop to idle?Thanks Jim. Wise words. Dwain is both seriously knowledgeable and immensely charitable. And here I am an undeserving goofball with grace pouring out on him. With the help of Dwain and others here I have gone from barely knowing how to turn this thing on to having a decent working knowledge of it in a short period of time. Trial by fire, I thank God for you all.
Jim about going to a local service center... I did! The folks you know very well that you and I have talked about. They said no, we won't work on it! After I drove 2 hours round trip twice! I really just wanted them to get it in good working order so I could learn the basics and figure out how to repair and maintain it later. When the engine idle wasn't correct those guys said they won't touch that part of a pto style system
It's working well now. Occassionally the machine shuts down without having tripped any recovery tank or water box sensors. I am hoping it has something to do with the tachometer when I look into that soon. Otherwise turning it off and rebooting it seems to get it working fine, then it runs as long as I need it to.
Van engine just suddenly drops to normal van idling of about 600 or so rpm. But the machine stays on. Good question, I stated the issue incorrectly.
My machine does that every once and a while about once every two weeks or so. It has to do with the throttle controller. I think it loses momentary contact some how with the engine control module or ground/brake set.
Thats where the led lights on the controller would come on handy. Till you restart the controller will self diagnose. In my case its buried deep in my dash and not easy to see.
You might check the wire on the machine end. Mine is connected to the on /off or more correctly the clutch in/ clutch out switch on my machines dash.
There's only three wires/circuits that can cause this from the machine, the wire that supplies power ie: tells the controller the machine is clutched in, next world be ground witch would kill the power to controller third would be the emergency brake sensor wire making the controller think the emergency brake was disengaged. Other than that the vans ecm is sending error signals ie: foot on brake, transmission in gear etc those would be showing in the self diagnostic leds on the controller. You might want to spend some time with the controller's manufacturers tech support. There always available and very helpful. Mine does it so seldom that i live with it but if it's happening frequently i would give them a call. You could also have a defective throttle controller and they can help you with that too
If the controller went completely dead it Sounds like the 12+ wire from your machine to the controller or the ground might need to be checked possibly where they start not at the controller
If you're unsure if the parking brake wire is causing problems that safty feature can be bypassed by removing the wire from the controller parking brake terminal then connecting the park brake terminal to the negative terminal on the controller. that will tell the controller that the park brake is always engaged
Their pretty good there at inpower. I thought you had a power problem. Because you said no lights . You'll need to trace out the ground and 12Ă· wire. It's more that likely the connections the probability have crimped fittings , if so my suggestion is to replace and solder and srink wrap. As fo the p0174 code in most cases its something simple. The sensor that monitor lean are the mas air flow and the o2 sensors. Most always its one of these sensors or a vacuum leak. Do you own an engine analyzer? If so will it graph live data? You'll need to see the o2 sensors in action to diagnose . Vacuum leaks can be checked with smoke or starting fluid . I recommend smoke. You can youtube how to build a simple smoke machime with a cigarette andhow to use it mass air flow sensor can be cleaned and should be done regularly only use map or maf sensor cleaner only. The sensor is located on the intake tube after the air filter and before the throttle body. Iclean mine every other oil change the code that is spit out will tell you which side of the engine the problem is on bank one is the side of tje engine #1 cylinder is on . As
Forgot, when tracing the wires make sure that the ground wire is connected to a dedicated body ground( where other manufacturers grounds are attached) not just machine screwed into the body. somewhere, do you have a test light? If not i would recommend you get one but get a low draw led. Read all the information before you buy you want one that is safe around sensitive Electronics like your ecm bcm tcm incandescent and halogen bulbed testers can damage sensitive Electronics
I dont know how mechanically inclined you are, or the extent of knowledge you have of vehicle engines and systems. P0174 code can be something major like head or intake manifold gaskets bad catalytic converter or something as simple as a loose/ cracked or disconnected vacuum hose, dirty or bad maf or o2 sensor. Depending upon your knowledge/ tools/time you might consider having a mechanic look at and repair the van and considerate your energy on the machine side. Eighter way if you need any advice im more than happy to help also have complete factory service manuals for 1998 & 2020chevy vans these manuals are several hundred pages and have all the information that dealers have on there computers but in print form the manuals are specific to the year but the information is good for the model run. Ie: frankinstien is a 2020 but my manuals are for a 2019 & bought my ford ranger service manual for my 2005 ranger but when i totaled it and bought a 2009 i used the same manuals
Heres a simple,backyard redneck non professional way to tell if you have a vacuum leak find a long steep grade to drive up , one where you can drive at least 50mph and your transmission will have to downshift. Now at the bottom of the hill turn your air-conditioning or heater on high. Set controls so as high air blows outa dashboard vents. When you're climbing up the grade be aware of the air flow from the vents. If somewhere when the engine is working hard the air stops coming outa the vents you have a vacuum leak. Now to explain whats going on. When the engine is working hard the manifold vacuum drops. Your vents are vacuum actuated , if the vacuum drops your vents will go to the default setting which is defrost/floor till the vacuum builds and the go back to setting. No this wont tell you where the leak is but you can get an idea how bad by how quick you loose and gain back the air flow your van has a vacuum reserve tank that normally would supply vacuum durning the times the engine doesn't provide adequate amounts but with a leak that will deplete that quickly
Mine was doing that because of the evap.
