Bane Wand Flow questions

[Mikey P]

I got a guy using a bane set up with it's OEM 3 jet wand w/ 6 flow (11002 X's 2) and he wants to get a Chosen Wand which comes with a stock 4 low set up (9502)

Because the bane system relies on low pressure(he runs 180 psi) and high('er) flow, should I set his wand up with two 9503's?

All my truckmount guys love the Chosen's 4 flow as it gets the same results as 6 flow wands wit less water (faster drying!) and I only tweak the flow for small porty guys with 2 or 3 flow total...

Thoughts?

 

[Dwain Ray]

I got a guy using a bane set up with it's OEM 3 jet wand w/ 6 flow (11002 X's 2) and he wants to get a Chosen Wand which comes with a stock 4 low set up (9502)

Because the bane system relies on low pressure(he runs 180 psi) and high('er) flow, should I set his wand up with two 9503's?

All my truckmount guys love the Chosen's 4 flow as it gets the same results as 6 flow wands wit less water (faster drying!) and I only tweak the flow for small porty guys with 2 or 3 flow

Tried to find the answer for you no google but after asking the exact same question 4 times and getting 3 different answer. I deleted the information. I can send you a standard spraying systems flow chart and the math to modify the psi if youd like. Or go with what Google tells you i asked " what's the flow rate of a 11002 vee-jet @ 180psi spraying water" when i add spraying water the answer was the same twice

 

[BIG WOOD]

At 180psi, I wouldn’t go over 4flow

 

[Mikey P]

At 180psi, I wouldn’t go over 4flow

same, but it makes me wonder what Bill was going for...

 

[Jack Zipper Zerkie]

What does Bain use as a blower for recovery.That would help to decide what to use. Never put down more than your unit can extract.

 

[Cleanworks]

I got a guy using a bane set up with it's OEM 3 jet wand w/ 6 flow (11002 X's 2) and he wants to get a Chosen Wand which comes with a stock 4 low set up (9502)

Because the bane system relies on low pressure(he runs 180 psi) and high('er) flow, should I set his wand up with two 9503's?

All my truckmount guys love the Chosen's 4 flow as it gets the same results as 6 flow wands wit less water (faster drying!) and I only tweak the flow for small porty guys with 2 or 3 flow total...

Thoughts?

I would stick with the six flow. With the lack of pressure, he needs more flow to flush the carpet. I like the 4 flow but I am using 350-400 psi on the portable and 500 psi on the truck. I have an old portable with a 150 PSi pump and the 4 flow on it sucks.

 

[Mikey P]

I would stick with the six flow. With the lack of pressure, he needs more flow to flush the carpet. I like the 4 flow but I am using 350-400 psi on the portable and 500 psi on the truck. I have an old portable with a 150 PSi pump and the 4 flow on it sucks.

Good point!

 

[Numero Uno]

What does Bain use as a blower for recovery.That would help to decide what to use. Never put down more than your unit can extract.

Sutorbilt 3m...

 

[Mikey P]

I think I'll send him both options to mess around with..

 

[Kenny Hayes]

I would use my truckmount Aw29
with slot glide with it and there was no difference. I used it as a porty, so there's that. Probably what Ron said.

 

[jeffexe]

I have to agree with staying with the 6 flow for flushing. I have a 200psi kleenrite small portable. I occasionally use it for highrise apartment carpets. I use the 4 flow if the carpets just need dusting. However, If they are soiled, I use 6 flow for better flushing action. I just take a couple extra dry strokes with the 6 flow.

 

[Nate The Great]

Sutorbilt 3m...

But severely under driven

Spins at 1275 RPM max

They attempted to change the direct coupling to drive it at a higher RPM but it Just trips Breakers


We tried to run to blowers parallel and tripped breakers


Stick with 6 flow MAX


If not you will leave carpets wet for 24 hours

 

[Kenny Hayes]

What a pita to lug the thing around like a porty even When they say it was built like a tank, they meant it!