Equipment upgrade- Is this a good plan?

[Mikey P]

Thanks so much for this- SUPER helpful! Very grateful for the details, and yes, I’d totally be open to learning more about encap and the Phoenix at Mikey’s Fest.

ARCBEST will probably charge you $1k to pick up and deliver...

Home | ArcBest

ArcBest is a multibillion-dollar freight and logistics solutions provider that solves complex supply chain challenges.

arcb.com

 

[Kenny Hayes]

He did say he is a teacher and this is a side gig. I can read Man, for commercial, a Cimex is the ticket if you have something other than a van to haul it. Even a 4/6 trailer is awesome for vlm equipment. Mikey hated his Cimex I know because of “lugging” it. It would be awful loading and unloading in a van! I pull trailers for floor jobs, so loading vlm equipment is no problem for me.

 

[Kenny Hayes]

Hey all the old idiots on here.

Bawb, Pigmanmarty, etc. This is why I had a trailer and I don't want to hear any excuse otherwise. When limited source of income doesn't allow for an extra vehicle...a trailer always provides a way to get started.

I have 3 trailers. Different sizes. They’re an asset to my business model. I have a tm in one and always used it on the occasional residential I would do. It was never an issue for me. However, if residential was my primary biz, I wouldn’t have liked it. That’s why I put a tm in my van even for the occasional residential job.

 

[Kenny Hayes]

I would buy Mike’s Ranger for cheap, since that’s already your thinking. I’m sure he didn’t use it much. I’m shocked he has it (sorta) A PEX probably runs 4K now.

 

[Mikey P]

He did say he is a teacher and this is a side gig. I can read Man, for commercial, a Cimex is the ticket if you have something other than a van to haul it. Even a 4/6 trailer is awesome for vlm equipment. Mikey hated his Cimex I know because of “lugging” it. It would be awful loading and unloading in a van! I pull trailers for floor jobs, so loading vlm equipment is no problem for me.

I never said or recollect saying that I hated the Cimex due to its weight, I grew to hate it over time when I realized I could actually be removing soil with a good op machine

 

[Kenny Hayes]

I do. You have said you hated lugging it around! I have you on tape!

 

[Mikey P]

I do. You have said you hated lugging it around! I have you on tape!

Liar!

I was a pro...


View: https://youtu.be/u_DZOirt_QU?si=E9dLrtb_0ZKyYPM9

 

[Mikey P]

View: https://youtu.be/yhviCuZfO6o?si=BD1jga78KC5GE3Vt

 

[Kenny Hayes]

You were smart then! (sorta) That loading process lacked a little to be desired! That’s the way I still do most commercial with my “ on demand” water supply. Pulling even a little 4/6 trailer beats that loading. Neither one of us was using TOPS prespray then, right? It is the cats ass with Releasit!

 

[Will D]

Will if you want this machine let me know soon otherwise I'm going to list it on Facebook marketplace this weekend

Wow Mikey you rock to give me the first shot at it! Will PM you.

 

[Will D]

As Mikey said, I would recommend the PEX 500 over thee Ranger. As have been said before, it a Swiss Army Knife of portys. The release valve to change from tool to tool is awesome. Two cords of course but there is a circuit breaker light indicator. It has high, low heat, and you can move it effortlessly. It loads fairly easy, and you can even lay it down to transport. It has a side discharge hose and a hose hanger. For a porty, it’s awesome. Put that with an orbital or a Cimex, and bam for commercial. I use my TMs vey little.

Love this. Ok, I'll do more research on the PEX500 for sure! Thanks!

 

[Will D]

No matter how you look at it a portable is a pain. Like many here I started out with a portable. A US Products Solus 310. I ran 25' of 1.5" hose with a 2 jet Evolution wand.

In the beginning I was always thinking I needed more vac and psi. But I learned that with proper wanding my dry times were just fine. As far as psi I found that 310 was more than enough with proper chemistry and agitation.

A 175 does wonders for portable users. I would use it to agitate my prespray and post bonnet after extracting. It completely changed my game and results.

I would also recommend that instead of getting an inline sprayer, you get a battery sprayer like a Multi sprayer or a SOS Gentoo. I have found them to be much quicker than a inline, especially if you have a limited to hose run. An inline also uses up your freshwater supply. Adding water and dumping water really cuts into production. I know you wanna run auto dump and fill, but it's not always available.

My recommendation would be to run whatever portable you can get for the cheapest and then move on to a truckmount. There's some really great deals out there.

I know a van can be an added expense, but depending on what your location is a trailer is a great way to get a truckmount without the added expense of a van and insurance. You can use your personal rig to tow it and also use your vehicle as a tax deduction. You can store all your equipment in there as well. It's like having another garage. If you live in a huge city where parking sucks than a van is a better option.

In carpet cleaning everything boils down to efficiency. If it isn't going to make you more efficient then you don't need it.

Lots of really good ideas here, very helpful. My church actually has a Multisprayer that they bought during COVID and haven't used since. I bet I could buy it off them for cheap. It doesn't have a battery though, plugs in.

 

[Mikey P]

plugs in

Their sprayer option is kinda lame as anything bigger than a 2AH cuts off the lance holder

 

[Living The Dream]

Lots of really good ideas here, very helpful. My church actually has a Multisprayer that they bought during COVID and haven't used since. I bet I could buy it off them for cheap. It doesn't have a battery though, plugs in.

I still have a plug in one that I bought used years ago. You sometimes have to unscrew the lance to get it to prime, but it only takes a sec. Try and get some extra jugs. I will usually fill all my extra jugs with hot water before leaving the shop. Then I just mix prespray as needed.

The multi sprayer also works good for applying solvent sealer. Most solvent sealer is rtu, so you just stick the jug in the multi sprayer and apply it as needed.

 

[Kenny Hayes]

Hydraforce with the PEX isn’t an issue. Can’t deny a separate sprayer is efficient. But a good pump up works well when you don’t want to use a hydraforce. That’s what I do for encapping. They are faster.