jstucky
Member
- Joined
- Sep 12, 2008
- Messages
- 451
- Name
- Jordan Stucky
I still haven't given up on this piece of poop....put new motor in like I said and all that jazz from previous post...
viewtopic.php?f=1&t=22173&p=244865#p244865
Wasn't doing ok for about a day..then started to lock in at 400-500 right when I turned the dial on...then would go down to 400 and lock in at that when I triggered it..was not giving a strong impact on carpet...
Used last night at Restaurant...it is where I have had issues with it alot and the Big Movie theatre I do...AT THESE PLACES I am running 30-50 ft of drop cord which is strandard length..but...it is cheap thing reg drop cord...were some of you right when you said the places maybe aren't supplying enough power??...Or it is a electrical issue...
Last night at Perkins it would not go above 300...mainly stayed at 200...cleaned the whole place at 200...Boosted with alot of Citrus Solv with US Products degreaser...still had good heat...just not alot of pressure....
I brought it in our garage today...hooked up the two seperate cords on seperate circuits and turned the dial on and it went up to 500 and when I triggered it went to 400 and locked in at that...
I turned the heat re-circulator system on and then off and it put the pressure guage back down to zero!...It takes about 5-10 seconds to climb up 2 500 and takes a few to go back down to zero...
The Unlaoder was new a while back and had issues a couple days after we replaced it...motor is 3 days old...A small black puddle of water is under the motor after using it for a while...leaky pump???
It takes 5 seconds to get up to 400-500 psi and dials down realllly slow..when I first replaced the motor it was pinpoint and quiccck..
US P said today I need to rebuild the Piston and seals in pump to fix black puddle...we rebuilt with O-rings and valves about 6 months ago...He also said it has to be the Unloader...so to replace that AGAIN...
Can anyone help...
Praise the Lord...John L might trade this for me at Mikey Fest 09...Please before I throw it off a freaking cliff....
Thanks all
Jordan
viewtopic.php?f=1&t=22173&p=244865#p244865
Wasn't doing ok for about a day..then started to lock in at 400-500 right when I turned the dial on...then would go down to 400 and lock in at that when I triggered it..was not giving a strong impact on carpet...
Used last night at Restaurant...it is where I have had issues with it alot and the Big Movie theatre I do...AT THESE PLACES I am running 30-50 ft of drop cord which is strandard length..but...it is cheap thing reg drop cord...were some of you right when you said the places maybe aren't supplying enough power??...Or it is a electrical issue...
Last night at Perkins it would not go above 300...mainly stayed at 200...cleaned the whole place at 200...Boosted with alot of Citrus Solv with US Products degreaser...still had good heat...just not alot of pressure....
I brought it in our garage today...hooked up the two seperate cords on seperate circuits and turned the dial on and it went up to 500 and when I triggered it went to 400 and locked in at that...
I turned the heat re-circulator system on and then off and it put the pressure guage back down to zero!...It takes about 5-10 seconds to climb up 2 500 and takes a few to go back down to zero...
The Unlaoder was new a while back and had issues a couple days after we replaced it...motor is 3 days old...A small black puddle of water is under the motor after using it for a while...leaky pump???
It takes 5 seconds to get up to 400-500 psi and dials down realllly slow..when I first replaced the motor it was pinpoint and quiccck..
US P said today I need to rebuild the Piston and seals in pump to fix black puddle...we rebuilt with O-rings and valves about 6 months ago...He also said it has to be the Unloader...so to replace that AGAIN...
Can anyone help...
Praise the Lord...John L might trade this for me at Mikey Fest 09...Please before I throw it off a freaking cliff....
Thanks all
Jordan