What jet set up would flush better

[Mikey P]

4 jets..01s at 600 psi

OR

4 jets..02s at 300 psi?

 

[Nate The Great]

What type of carpet?

 

[BIG WOOD]

.01's shouldn't be allowed to be on a wand

 

[hogjowl]

We settled this on ICS years ago.

 

[jcooper]

4 jets..01s at 600 psi
OR
4 jets..02s at 300 psi?

I'd rather go over the areas more than once with 300 psi than blast the poop out of them at 600psi.

95% of the time I'm 400psi with 02 jets.

 

[Mikey P]

We settled this on ICS years ago.

Would you rather talk about child molesters?

 

[Mikey P]

I'd rather go over the areas more than once with 300 psi than blast the poop out of them at 600psi.

95% of the time I'm 400psi with 02 jets.

What kind of heat is your 370 holding at 8 flow


Mine with my 9 flow 360i does well but the aggitator is doing far more than the heat.

 

[Tony Wilson]

Running prochem quad w/1.5s at 400 psi. Seams good. Should I bump the psi? Should I go bigger? 4.8 blower so recovery is no a problem. Just always concerned about over wetting. I spray forward and bs k then double dry pass with slotted glide.

 

[Jimmy L]

As far as child molesters they have to prove Marty was one first.

BUT HE'S NO DAISY!

 

[dealtimeman]

Depends

 

[Lyman]

Marty is wearing depends. 02 at 450 baby

 

[steve_64]

I'd rather go over the areas more than once with 300 psi than blast the poop out of them at 600psi.

95% of the time I'm 400psi with 02 jets.

I felt the .02 caused more fiber distortion even at lower pressure so I switched to .015. still get it but not as bad.

I may try them again, it's been awhile since I used them.

 

[hogjowl]

We determined it didn't matter unless your TM was one of DooDaddys.

 

[Cleanworks]

4 jets..01s at 600 psi

OR

4 jets..02s at 300 psi?

The 8 flow will flush better. It's like washing your car. When it's time to rinse the soap off, what works faster? High pressure nozzle on thin stream, or low pressure on a broader flow?

 

[Larry Cobb]

#4 @ 600 PSI =1.55 GPM
#8 @ 300 PSI = 2.19 GPM - Winner . . . more Impact, Better Cleaning,

Decent TM's will do better with even more GPM.

 

[Mikey P]

My worn out 012 flow for jetter Ti is the king

 

[Larry Cobb]

The 4 Jet Ti was one of the best Ti wands.

Your 012 flow is limited by the 1/4" solution line,

but still going in the right direction.

 

[GeeeAus]

8 flow at 300 PSI

 

[Bob Savage]

I clean at 400 PSI with 4 #02 jets on a 2" TI wand.

When the wand is keyed, the 400 PSI drops to 350 PSI.

When the second wand is keyed the pressure drops to 335 PSI. The second wand has 2 #9503 jets.

I have found this setup gives me great cleaning/flushing without over-wetting.

 

[SamIam]

Ya flush hard with 1.5-3.0. To the 5 th power and 1-/2 inch hose

LARRY COBB

On Samiam's phone.


Oh ya that flow chart was @dgardner work peace.

 

[Lee Stockwell]

Experiment for yourself and then tell us who is FOS.

 

[BIG WOOD]

Experiment for yourself and then tell us who is FOS.

I'm wondering why mikey is pushing a 4flow. He's even selling a 4flow wand.

There's gotta be a motive

 

[SamIam]

I'm wondering why mikey is pushing a 4flow. He's even selling a 4flow wand.

There's gotta be a motive

Ya it's called a 370 hahahahA

 

[Larry Cobb]

Spraying Systems has lots of jet impact info.

Double the GPM and you get DOUBLE the impact.

Double the PSI and you get 1.44 x the impact.

Most T&G cleaners are running two #0502 jets.

We have been changing them to two #0503 jets,

and seeing a significant increase in cleaning power (50%) .