BlueLine Thermalwave2 summer/fall project

[BIG WOOD]

I’m taking it to the forklift later this week to move it. Rubber mats underneath are getting pulled up.

The waste tank was behind it but I think I’m gonna move it to the left side of the machine for better mounting space and ease of access to the rear and right side of the machine.

The van needs a power steering fluid reservoir, a tuneup, and a new rear door

As for the tm, the water pump needs tlc, and the 185f thermal relief valve needs replaced. . Once I get it completed, we’ll see what other issues it might have

 

[Justin Legend Brands]

Thanks to your updated manual…it showed where the plumbing I had currently .from my manual, was preventing the hot water to return back to the water box. And since my unit doesn’t have a solenoid, the hose #24 was routed to the pressure regulator so the water would stop moving.

And to complete the day even better…the headers didn’t overheat and glow during testing. I hope it stays that way. I’ll be burning extra clean gas for the next few tanks to make certain it stays that way

Thanks again @Justin Legend Brands

And @Jim Martin , your help was Greatly appreciated as well.

View attachment 113018 View attachment 113019


Thanks to your updated manual, The temp loss problem has finally been fixed. I have yet to find out if it can compete with the everest heat (I need to put it on a full day of work), and the headers did not start overheating with red glow today.

So this project is ready to be sent out to work. Thanks @Justin Legend Brands , and @Jim Martin

View attachment 113022 View attachment 113023

Not going to lie, I am going to miss sending you Gifs... Maybe I will randomly send them...

 

[hogjowl]

I have a couple of morons who do that to me

 

[BIG WOOD]

Nate's asshole comment reminded me to update:

I just got the van back today. Needed a tune up and the mechanic put a new alternator, belt and belt tensioner on the van's engine. I also had him check the fuel pressure on the tm.

It's only reading 30psi. This model requires 50+

So that's the cause of the headers glowing. Last and final job of replacing the fuel pump and fuel lines. Then I'll feel comfortable to rely on a full day of work with it.

My mechanic suggested I get the Walbro 225 or 190 with 6AN fuel line kit. Look more affordable than what JD wants (over $600!)

Any ideas on which model will be best for this setup?

 

[Nate The Great]

Nate's asshole comment reminded me to update:

I just got the van back today. Needed a tune up and the mechanic put a new alternator, belt and belt tensioner on the van's engine. I also had him check the fuel pressure on the tm.

It's only reading 30psi. This model requires 50+

So that's the cause of the headers glowing. Last and final job of replacing the fuel pump and fuel lines. Then I'll feel comfortable to rely on a full day of work with it.

My mechanic suggested I get the Walbro 225 or 190 with 6AN fuel line kit. Look more affordable than what JD wants (over $600!)

Any ideas on which model will be best for this setup?

Wow, just wow..

Walbro 225 is a good all around pump..

 

[BIG WOOD]

Wow, just wow..

Walbro 225 is a good all around pump..

I'm glad I didn't replace the Catalytic converter. That would've been $800 wasted. And I'm also glad I didn't clean or replace the fuel injectors. No telling how much money and time would've been wasted there. I wish I had more tools handy to check simple stuff like this. It would've saved me so much time trying to figure it out

 

[Dolly Llama]

It's only reading 30psi. This model requires 50+

what problem does that cause?
runs too lean?


..L.T.A.

 

[Mikey P]

How many Saturdays wasted on this pos so far?

 

[Kenny Hayes]

Brutal

 

[BIG WOOD]

what problem does that cause?
runs too lean?


..L.T.A.

The engine burns hotter, causing headers to glow. Remember Scott’s Steam Action glowing? It’s burning too lean.

 

[BIG WOOD]

How many Saturdays wasted on this pos so far?

Too many. But $15000 spent is better than $45k on a new one this size

 

[Nate The Great]

Too many. But $15000 spent is better than $45k on a new one this size

Idk man.. I got a Everest650hp 4k hours on it for $10k.. Well, $11k with shipping pre-covid.. It's still sitting on the pallet it got shipped on..

I wish I was your supplier/mechanic, I could sell an eskimo ice.. I'm going to call your Sparky from now on.. Cuz plugs is too brutal..

 

[Nate The Great]

what problem does that cause?
runs too lean?


..L.T.A.

Makes me wonder if you can do the diesel redneck hack to it instead of buying a new lift pump.. Basically putting a shutoff valve on the return line to restrict the flow of the return to boost the pump pressure..

 

[Mikey P]

How many Seasons wasted on this pos so far?

 

[BIG WOOD]

3 so far

 

[Justin Legend Brands]

I also had him check the fuel pressure on the tm.

It's only reading 30psi. This model requires 50+

I just checked out text messages, I asked about fuel pressure 2+ months ago. I am pretty sure I mentioned it on the phone with you too, but I don't have any proof.

 

[Nate The Great]

Legend Brands" data-source="post: 4797765" class="bbCodeBlock bbCodeBlock--expandable bbCodeBlock--quote js-expandWatch">

I just checked out text messages, I asked about fuel pressure 2+ months ago. I am pretty sure I mentioned it on the phone with you too, but I don't have any proof.

Sparky only hears what he wants to hear..

 

[BIG WOOD]

Legend Brands" data-source="post: 4797765" class="bbCodeBlock bbCodeBlock--expandable bbCodeBlock--quote js-expandWatch">

I just checked out text messages, I asked about fuel pressure 2+ months ago. I am pretty sure I mentioned it on the phone with you too, but I don't have any proof.

Yeah, I remember that conversation. It took 2months to get my mechanic to check it

 

[Mikey P]

Sell that piece of shit and buy a OP machine already

 

[BIG WOOD]

Aaaaand…another stupid finding


I was never fully satisfied with the heat. So I kept testing it and noticed the thermostat housing right above the coolant heat exchanger is almost 100f hotter than the heat exchanger. So I’m thinking the thermostat is bad

Well, I take it off, only to see the housing with NO FKIN THERMOSTAT! It’s been bypassing the heat exchanger the whole time. So I go to the auto parts store and get the recommended one, only to discover it’s too big to fit in the seat of the housing.

If anyone knows the part number to fit this housing, I’d appreciate it.

 

[FredC]

Is this what you meant by recommended one?

THERMOSTAT, NISSAN A-15 195 DEG

Nissan Engine Thermostat 195 Degree (36‑127)

T-Stat #195 Nissan

www.jondon.com

I looked locally auto store for a 195degree for a 1981 Datsun 210/310 (which I assume is the same part)but only found 180

for cross reference

CarPartsDiscount.com - Online Auto Parts

Up to 75% off list price at CarPartsDiscount.com! Fast shipping of genuine OEM & aftermarket components, warehouse-direct to shops and DIY mechanics.

www.carpartsdiscount.com

*shows the nissan tstat in GM Manual

 

[BIG WOOD]

Is this what you meant by recommended one?

THERMOSTAT, NISSAN A-15 195 DEG

Nissan Engine Thermostat 195 Degree (36‑127)

T-Stat #195 Nissan

www.jondon.com

I looked locally auto store for a 195degree for a 1981 Datsun 210/310 (which I assume is the same part)but only found 180

for cross reference

CarPartsDiscount.com - Online Auto Parts

Up to 75% off list price at CarPartsDiscount.com! Fast shipping of genuine OEM & aftermarket components, warehouse-direct to shops and DIY mechanics.

www.carpartsdiscount.com

*shows the nissan tstat in GM Manual

I got the thermostat from a ‘76 Datsun b210

I’ll look up your reference and see if it pulls up a different thermostat

 

[Nomad74]

Please don't over-complicate this Matt.

 

[BIG WOOD]

Please don't over-complicate this Matt.

I’m trying hard not to. I really am

 

[FredC]

too big how?

 

[BIG WOOD]

too big how?

Too large in diameter to fit in the seat of the housing that the 90degree elbow bolts to

 

[FredC]

break your calipers out and tell us how big that is


and you were putting it in the right way right?

 

[BIG WOOD]

I should’ve taken the housing with me to fit it in at the store. That’s my project this weekend

 

[Kenny Hayes]

One more Saturday. Love Mikey!

 

[Nate The Great]

Get some extra spark plugs and leave in the glove box..






















LTA........ @Dolly Llama on Nate's computer..

 

[BIG WOOD]

The only ones that came up on the computer weren’t in stock. So I went through each one they had on the shelf and found this 192f I’ll hook it up tomorrow and see how well it works

It seated perfectly in the groove